Tag Archives: Pharmaceutical Manufacturing

ORAL SOLID DOSE – Architectural Considerations

Hello good people of the world! Today we’re talking about architectural considerations in the design of oral solid dose (OSD) manufacturing facilities.

In addition to normal architectural standards, the following must be considered for OSD manufacturing facilities:

  • Manufacturing process flow
  • Personnel flow
  • Equipment flow (clean and dirty)
  • Waste flow

Risks to consider when mapping flows include:

  • Risk of contamination from outside contaminates
  • Risk of cross-contamination
  • Risk of mix-up

Risk mitigations should consider:

  • Process containment
  • Isolators
  • Environmental controls
  • Room size
  • Transition spaces and airlocks
  • Personnel controls such as gowning
  • Administrative controls such as frequency of operation

Like this MWV (Mike Williamson Validation) blog post? Be sure to like, share, and subscribe!

Oral Solid Dose – Isolation and Containment

Hello good people of the world! Today we’re going to talk about isolation and containment considerations in oral solid dose manufacturing. The purpose of isolation and containment is to control the level of pharmaceutical ingredient exposure to personnel and the environment. It is typically not possible to eliminate all exposures, so we try to reduce it to a tolerable level, which must be defined.

The CFRs and other regulations require manufacturers to limit exposure to customers of any undesirable substance. Limits have been established by industry group and regulatory bodies, and quantify things such as Allowable Daily Exposure (ADE).

Things to look at when considering isolation and containment include:

  • Material flow
  • Personnel flow
  • Operator interventions
  • Sampling
  • Waste flow
  • Maintenance procedures
  • Utility interactions

Isolation and containment risks must be evaluated and mitigated to get a solid handle on the implications. A multi-disciplinary approach must be used. Migations may include:

  • Physical barriers
  • Air control
  • Cleaning procedures
  • Disposables
  • Training

What considerations come in to play in your isolation/containment strageties? Comment below!

Like this MWV (Mike Williamson Validation) blog post? Be sure to like, share, and subscribe!

ORAL SOLID DOSE – Supporting Equipment and Systems

Hello good people of the world! Continuing the series on oral solid dosage forms, today we’re going to talk about supporting equipment and systems. The main equipment in unit operations get the spotlight when it comes to manufacturing Oral Solid Dosage forms, but they cannot work without supporting equipment and systems.

Supporting Equipment:
Typical supporting equipment in a OSD manufacturing process includes:

  1. Air Systems: all modern manufacturing processes use air systems for process, instruments, and environment. HVAC helps control environmental conditions, including particulate (viable and nonviable) counts, temperature, and humidity. Compressed air systems may be used in the process to cool or cover product, such as with nitrogen, or operate unit operation steps, such as in fluid bed drying. Automated systems will use compressed air to pneumatically control valves and other components.
  2. Dust Collection: compared to biotech and other pharmacuetical processes, OSD processes have the added complication of dust collection. OSD material movement and processes can create a lot of dust, which can be a risk from a product quality point-of-view, but also a safety point-of-view, since dust can lead to fires and even explosions. Dust collection equipment must be employed to minimize and control dust.
  3. Vacuum Systems: vacuum systems may be used for cleaning, dust collection, and also in process steps such as vacuum drying.

Supporting Systems:
Typical supporting systems include:

  1. Change Control: it is expected that engineering changes are controlled with quality oversight through a formal process.
  2. Preventive Maintenance: it is expected that regular preventive maintenance be performed and documented formally.
  3. Calibration: it is expected that “critical” instruments are calibrated at regular intervals traceable to an international standard. Calibration procedures and results must be formally documented. The method to determine and results of the determination of critical instruments must be documented.

What supporting equipment and/or systems do you use in your OSD manufacturing process? Comment below!

Like this MWV (Mike Williamson Validation) blog post? Be sure to like, share, and subscribe!

ORAL SOLID DOSE – Unit Operations

Granulator at an OSD Plant in Vietnam

Hello good people of the world! Continuing the series on oral solid dosage forms, today we’re going to talk about unit operations typical in a oral solid dose manufacturing process.

Typical OSD processes may include some combination of weighing/dispensing, material transfer, blending, granulation, drying, milling/sieving, compression, encapsulation, and coating. Some considerations around each step may include:

  1. Weighing/Dispensing: includes sampling for quality purposes. Materials to be sampled typically include: APIs, excipients, primary and secondary packaging, cleaning agents. Sampling areas must be protected from contamination.
  2. Material Transfer: material flows should be documented and reviewed, with the intention of minimizing any contamination.
  3. Blending: materials are typically blended to ensure a uniform composition, prior to downstream process steps. Many methods exist, including: tumble blending, bin blending, and agitator mixers.
  4. Granulation: granulation is the process of combining particles into a granule. Many methods of granulation exist: wet massing/extrusion, high shear, spray, speronization, and hot melt extrusion, for example.
  5. Drying: the purpose of the drying step is to remove any excess moisture from the drug product. Drying methods include: tray , fluidized bed, and spray drying.
  6. Milling/Sieving: the purpose of this process step is to reduce granule size to conform to specification. Some methods include: impact/hammer mills, conical mills, and oscillating horizontal screens.
  7. Compression: compression is used to create tablets.
  8. Encapsulation: encapsulation is used to create capsules.
  9. Coating: coating is used to apply a coat to tablets

In the next post we’ll cover supporting equipment and quality systems. What process steps do you use in your OSD process? Comment below!

Like this MWV (Mike Williamson Validation) blog post? Be sure to like, share, and subscribe!

Oral Solid Dose – Material Handling

Hello good people of the world! Continuing the series on oral solid dosage forms, today we’re going to talk about material handling. Oral solid dose manufacturing is typically a batch process, which means materials need to be transferred from step-to-step. Sometimes there is direct conveyance between steps, but often transfer is performed via Intermediate Bulk Container (IBC).

In terms of design, IBCs should be able to handle the worst-case (lowest) density material in the process. IBCs should be cleanable, especially if a single container will support many product manufacturing processes. IBCs should be designed in such a way that they drain easily. Charging/discharging must be considered.

IBCs may be transported on wheels, or by a pallet truck.

Discharging may be facilitated by applying vibrations to the IBC, either internally or externally.

For direct conveyance, gravity, pneumatic conveyance, and mechanical conveyors are options.

What considerations around material handling do you have in your OSD lines? Comment below!

Like this MWV (Mike Williamson Validation) blog post? Be sure to like, share, and subscribe!

Oral Solid Dose – Equipment Cleaning

Hello good people of the world! Continuing the series on oral solid dosage forms, today we’re going to talk about equipment cleaning. OSD manufacturing equipment can be notoriously hard to clean, and manual cleaning procedures introduce high risk of contamination and carryover. It is recommended that any new or existing process equipment be cleaned with automated processes wherever possible.

The three automated cleaning processes typically used in industry are:

  • Clean-in-Place (CIP)
  • Wash-in-Place (WIP)
  • Clean-out-of-Place (COP)

CIP is done without moving the equipment, as the name implies, and uses a CIP skid to deliver cleaning and rinse solutions. CIP should not require any manual operations.

WIP is done in-place as well, but may include some manual operations, such as removing filters.

COP requires equipment to be moved to a wash station. Tanks and vessels are typically COP’d.

Some specific concerns related to cleaning OSD equipment include:

  • Dry Granulator/Roller Compactor cannot typically be CIP’d. Particularly the auger must be removed and COP’d.
  • Fluid Bed Dryers a large and complex, making cleaning difficult. Modern dryers will include CIP/WIP but typically still require manual cleaning of some parts.
  • Milling equipment typically requires the screen to be manually removed before any CIP/WIP.
  • Tablet presses can be difficult to clean, requiring many manual interventions prior to washing.
  • Capsule filling machines should be wettable to allow cleaning.
  • Tablet coaters should include WIP

Of course, cleaning processes, whether automated or not, need to be validated. Riboflavin tests may be performed to verify wash coverage, and swabbing can verify lack of residual API and cleaning solutions.

What challenges have you run into in cleaning your OSD manufacturing equipment? Comment below!

Like this MWV (Mike Williamson Validation) blog post? Be sure to like, share, and subscribe!